Injection Resin Ex-Hi Viscosity
Urethane Foams
Crack Paste
Chemical Anchoring
Joint Sealants
Pick-Proof
Liquid Concrete Repair
High Modulus Binders
Low Modulus Binders
Bonding Agents
Patching Gel
Grouts & Mortar
|
|
|
POLYJECT #1001-EHV
Maximum Penetrating Injection Epoxy
|
|
1. PRODUCT NAME
POLYJECT #1001-EHV |
2. MANUFACTURER
Polygem, Inc.
1105 Carolina Drive
West Chicago, IL 60185
Telephone: (630) 231-5600
FAX: (630) 231-5604
Internet: www.polygem.com
|
3. PRODUCT DESCRIPTION
POLYJECT #1001-EHV is a 100% solids, two component, moisture insensitive, extra high viscosity epoxy gel designed to permanently restore structural and design strength to cracked concrete structures. Unique wetting properties allow maximum penetration into cracks as thin as .025”.
POLYJECT #1001-EHV can be used on wet or dry surfaces as well as underwater. It exhibits the ability to push away water to seal cracks in basement walls, thus preventing air and water leaks.
ADDITIONAL USES: Repair cracked basement floors, concrete ceilings, wood beams, parking garage decks, bridge supports, underwater piers, exterior slabs, grain elevators, etc. Available: Standard pot life, long pot life, fast set.
Advantages / Features
- DOT APPROVALS
- MEETS ASTM C881 TYPE I, II, IV & V, GRADE 3, CLASS B & C
- RESTORES STRUCTURAL STRENGTH (Provided original cause of crack is eliminated)
- STOPS WATER AND AIR LEAKS
- WORKS ON DRY OR WET SURFACES EVEN UNDERWATER
- PENETRATES CRACKS .025” AND ABOVE
- AVAILABLE IN GALLONS AND DUAL CARTRIDGE (16.5 oz)
- NO SHRINKAGE
- EXCELLENT ADHESION TO WOOD, CONCRETE AND METALS
- VOC COMPLIANT
|
|
4. APPLICATION INSTRUCTIONS
- Mix 2 parts A (Resin) to 1 part B (Hardener) by volume. Avoid mixing more than 1/2 gallon at a time.
- Utilize a slow speed drill with a mixing paddle for 1-2 minutes or until uniform in color. Do not exceed mixing over 3 minutes.
- Maintain ingredients above 50° F for optimum results. Unmixed material may crystallize if exposed to temperatures below 50° F.
- See “Recommended Concrete Crack Repair” for further instructions.
Consult Polygem for additional technical instructions
Packaging
3 gallon, 15 gallon, 150 gallon 10.3 oz. cartridge, 16.5 oz. cartridge
|
| 5.TECHNICAL DATA
Performance Properties
| Test |
Test Method Results |
|
|
| Slant Shear Strength ASTM C-882 2 days | 1200 psi (min)
|
| Slant Shear Strength ASTM C-882 14 days | 1520 psi (min)
|
| Compressive Strength ASTM D-695 | 14,480 psi (min)
|
| Tensile Strength ASTM D-638 | 8,315 psi (min)
|
| Tensile Elongation D-638 | 8.9% (min)
|
| Linear Coefficient of Shrinkage | <0.001
|
| Heat Distortion Temperature | >120°F
|
| Water Absorption, 24 hours | 0.1989%
|
| Shore D Hardness ASTM D-2240 | 80-75
|
| Gel Time @ 77° F | 32 minutes
|
| Pot Life @ 77° F | 15 minutes
|
| Cure Time @ 77° F | 3-5 hours
|
| Mix Ratio | 2 to 1 by volume
|
| Viscosities @ 77° F | Gel
|
|
|
|
| Polygem, Inc. warrants its products to be free of manufacturing defects and that, at the time and place of shipment, our material will meet current physical properties when applied within Polygem’s directions and tested in accordance with ASTM and Polygem standards. Polygem, Inc’s liability is limited to replacement of material found defective. As Polygem, Inc. has no control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and/or our information is valid in a particular circumstance. Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each product. Nothing contained herein shall be construed to be a recommendation to use or as a license to operate under or to infringe any existing patents.
Data sheets are subject to change without notice, for latest revision check our website at www.polygem.com
|
|
