Decorative
Seamless Flooring
Protective Coatings
High Build
|
|
|
GEMCOAT #1324
100% SOLIDS HIGH GLOSS FLOOR COATING
|
|
1. PRODUCT NAME
GEMCOAT #1324 |
2. MANUFACTURER
Polygem, Inc.
1105 Carolina Drive
West Chicago, IL 60185
Telephone: (630) 231-5600
FAX: (630) 231-5604
Internet: www.polygem.com
|
3. PRODUCT DESCRIPTION
GEMCOAT #1324 is a tough, durable, yet distinctively decorative coating used to protect walls and floors against corrosion and deterioration. GEMCOAT #1324 is a 100% solids, moisture insensitive epoxy coating formulated to cure at room temperature. Designed to withstand the wear caused by forklift and other industrial machinery, GEMCOAT #1324 is ideal for industrial plants, auto dealer repair shops, garage floors, etc. GEMCOAT #1324 provides outstanding resistance to moisture and many chemicals. GEMCOAT #1324 is available in light gray and tile red. Additional colors can be matched upon request.
Advantages / Features
- SELF-LEVELING
- 100% SOLIDS - NO SOLVENTS
- MOISTURE INSENSITIVE
- V.O.C. COMPLIANT
- HIGH GLOSS
- EASY TO CLEAN
Uses
| Thickness of Coating Applied (100 mils = 1 in.) |
Coverage per U.S. Gallon 100% Solids System |
| 1/4 in. = 250 mils | 6.4 sq. ft. |
| 3/16 in. = 187.5 mils | 8.5 sq. ft. |
| 1/8 in. = 100 mils | 16.0 sq. ft. |
| 1/16 in. = 50 mils | 32.0 sq. ft. |
| 1/32 in. = 20 mils | 80.0 sq. ft. |
1/64 in. = 10 mils
5 mils | 160 sq. ft.
320 sq. ft. |
|
|
4. APPLICATION INSTRUCTIONS
- Surface should be prepared by using conventional cleaning methods such as shot blasting, acid etching, disc grinding, sandblasting or mechanical abrasion. The surface to be coated should be free of loose materials, paints, sealants or oils. Use #20 solvent to remove oils and dirt.
- Blend 4 parts A (Resin) to 1 part B (Hardener). Mix with low speed drill until uniform color appears. DO NOT ADD SOLVENTS! Do not exceed mixing over 3 minutes.
- Apply to prepared surface with brush, short nap roller, squeegee or airless sprayer. Maintain temperature of material above 50°F. GEMCOAT #1324 can be applied with a trowel, squeegee or putty knife. Do not apply to wet/damp surfaces. Do not apply in humid conditions.
- Allow 8 hours @ 75° F for light foot traffic. Clean tools with #20 solvent for best results.
Consult Polygem for additional technical instructions
Packaging
5, 25, 250 gallon kits
|
| 5.TECHNICAL DATA
Performance Properties
| Test |
Test Method Results |
|
|
| Compressive Strength ASTM D-695 | 14,950 psi (min)
|
| Tensile Strength ASTM D-638 | 9,900 psi (min)
|
| Tensile Elongation ASTM D-638 | 4.8% minimum
|
| Flexural Strength | 13,800 psi
|
| Flexural Modulus | 405,000 psi
|
| Shore D Hardness | 90-85
|
| Gloss (Gardner) | 90
|
| Pot Life @ 75° F | 40 minutes
|
| Cure Time @ 75° F | 18-24 hours
|
| Viscosity (mixed) | 2,000 cps
|
| Ratio | 4:1 by volume
|
|
|
|
| Polygem, Inc. warrants its products to be free of manufacturing defects and that, at the time and place of shipment, our material will meet current physical properties when applied within Polygem’s directions and tested in accordance with ASTM and Polygem standards. Polygem, Inc’s liability is limited to replacement of material found defective. As Polygem, Inc. has no control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and/or our information is valid in a particular circumstance. Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each product. Nothing contained herein shall be construed to be a recommendation to use or as a license to operate under or to infringe any existing patents.
Data sheets are subject to change without notice, for latest revision check our website at www.polygem.com
|
|
