Decorative
Quartz
Seamless Flooring
Ultra Gloss
Protective Coatings
High Gloss
|
|
|
POLYBAC #1319 ULTRA
Ultra Clear Epoxy Coating
|
|
1. PRODUCT NAME
POLYBAC #1319 ULTRA |
2. MANUFACTURER
Polygem, Inc.
1105 Carolina Drive
West Chicago, IL 60185
Telephone: (630) 231-5600
FAX: (630) 231-5604
Internet: www.polygem.com
|
3. PRODUCT DESCRIPTION
POLYBAC #1319 ULTRA is a water-clear epoxy coating specially formulated for use as a top-coat in quartz broadcast seamless flooring applications to provide the ultimate in gloss and appearance. POLYBAC #1319 ULTRA is an easy to mix 2 to 1 by volume ratio. POLYBAC #1319 ULTRA is ideal for top-coat finishes that demand the clearest high-gloss finish epoxy coating available. POLYBAC #1319 ULTRA is resistant to water spotting and most chemicals and solvents. POLYBAC #1319 ULTRA can be pigmented for color coating of surfaces.
Advantages / Features
- Ultra-Clear formula.
- No VOC’s or Solvents
- 100% solids
- UV Resitant
Uses
For coating and sealing concrete, wood, metal and fiberglass surfaces to provide a high-gloss clear protective surface.
POLYBAC #1319 ULTRA is ideal for use on:
- Quartz Broadcast Flooring
- Top Coat/Clear Coats
- Crack Healing/Sealing
- Exposed Aggregate Resurfacers
- Epoxy Mortars and Grouts
- Waterproofing Concrete Block
|
|
4. APPLICATION INSTRUCTIONS
- POLYBAC #1319 ULTRA can be applied by squeegee, brush, roller or spraying.
- Clean surface by shotblasting or sanding to provide clean and open surface.
- Thoroughly mix measured amounts of 2 parts of Part-A Resin with 1 part of Part-B Hardener by volume until streak free. Scrape side and bottom of pail frequently during mixing to insure a good mix. Mix only enough that can be applied in 45 minutes.
- 4) Spread mixed epoxy with squeegee and back roll with a 3/8” nap roller until spread evenly onto the surface. Back-roll two times in a perpendicular directions and take care to avoid puddles or "dry spots" for best results
Consult Polygem for additional technical instructions
Packaging
POLYBAC #1319 ULTRA is available in 2 kit sizes:
3 Gallon Kits and 15 Gallon Kits.
Shelf Life
Factory sealed containers of this product are guaranteed to be of first quality for min. 24 months.
Limitations
Not for use on contaminated or oily surfaces.
Do not install when surface temperature is below 60°F (7°C) or above 85°F (32°C).
During damp and/or cool conditions epoxy will cure slower and protect finished work from traffic until fully cured.
Cautions
- Wear chemical goggles and NIOSH approved respirator. Wear proper protective clothing and gloves to prevent direct contact of resins. Consult Material Safety Data Sheet for full listing protective requirements.
- POLYBAC #1319 ULTRA may irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin.
- For professional use only.
- Keep out of reach of children.
|
| 5.TECHNICAL DATA
Performance Properties
| Test |
Test Method Results |
|
|
| Pot Life @ 77°F (100 gms) | 45 mins.
|
| Thin Film Set-Time @ 77°F | 10 hours
|
| Compressive ASTM D-695 | 12,650 psi
|
| Compressive Modulus | 425,000 psi
|
| Tensile Strength ASTM D-638 | 7,500 psi
|
| Flexural Strength | 12,300 psi
|
| Elongation ASTM D-638 | 4.3% min.
|
| Mix ratio by volume A/B | 2:1
|
| Mixed Viscosity | 750 cps
|
| Color Mixed | Clear
|
|
|
|
| Polygem, Inc. warrants its products to be free of manufacturing defects and that, at the time and place of shipment, our material will meet current physical properties when applied within Polygem’s directions and tested in accordance with ASTM and Polygem standards. Polygem, Inc’s liability is limited to replacement of material found defective. As Polygem, Inc. has no control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and/or our information is valid in a particular circumstance. Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each product. Nothing contained herein shall be construed to be a recommendation to use or as a license to operate under or to infringe any existing patents.
Data sheets are subject to change without notice, for latest revision check our website at www.polygem.com
|
|
