Waterproofing and Foundation Repair
LCR - Liquid Concrete Repair Repair Paste
How To
|
|
|
LIQUID CONCRETE REPAIR PASTE
EPOXY REPAIR PASTE
|
|
1. PRODUCT NAME
LIQUID CONCRETE REPAIR PASTE |
2. MANUFACTURER
Polygem, Inc.
1105 Carolina Drive
West Chicago, IL 60185
Telephone: (630) 231-5600
FAX: (630) 231-5604
Internet: www.polygem.com
|
3. PRODUCT DESCRIPTION
LCR EPOXY REPAIR PASTE is a unique new water clean-up epoxy repair paste designed to provide high-strength bonding for all types of repair projects. LCR is ideal for homeowners, contractors, remodelers, maintenance personnel and D.I.Y users.
Advantages / Features
- EASY TO MIX
- HIGH STRENGTH
- SANDABLE
- PAINTABLE
- NO SHRINKAGE
- SAFE TO USE
- PERMANENT REPAIRS
Uses
Bonds Concrete, Wood, Fiberglass, and Metal
- Concrete Cracks
- Driveways
- Sidewalks
- Patios
- Floors
- Pools
- Foundations
- Wood Rot Repair
- Laminating
- Shaping
- Gluing
- Auto Body
- Thread-Lock
- Pipe Repair
- Metal Joining
- Boats
- Hot Tubs
- Modeling
- Sculpting
- Anchoring
- Tile Adhesive
- Household Repairs
- Hobbies & Crafts
|
|
4. APPLICATION INSTRUCTIONS
- Surface. should be clean and dry.
- Mix equal amounts of Part A & Part B.
- Mix only small amounts that can be used in 20 minutes.
- Allow epoxy to fully cure for 24 hours
BONDING: - Apply mixed epoxy to both surfaces to be joined.
- Press together firmly and clamp or brace.
- Allow 24 hour cure before sanding or painting.
Anchoring: - Drill hole 1/8” larger than anchor.
- Fill hole half way with mixed epoxy and insert anchor with twisting motion. Epoxy should be level with surface when anchor is fully inserted.
- Do not disturb anchor for 24 hours.
Patching: - Apply mixed epoxy evenly over surface to be repaired.
- Water may be used on trowel or putty knife to obtain smooth surface
Grouting: - Add sand, gravel, sawdust or metal filings to mixed ppoxy to produce trowelable mortar for grouting.
- Allow 24 hours before sanding or painting.
Consult Polygem for additional technical instructions
Packaging
Part A and Part B: Net weight 17 ounces
Cautions
- KEEP OUT OF REACH OF CHILDREN!
- ALWAYS WEAR RUBBER GLOVES AND EYE PROTECTION WHEN HANDLING THIS PRODUCT.
|
| 5.TECHNICAL DATA
Performance Properties
| Test |
Test Method Results |
|
|
| Tensile Strength ASTM D-638 | 5,500 psi
|
| Compressive Strength ASTM D-695 | 14,500 psi
|
| Impact Strength ASTM D-256 | .22 ft. lbs./in. notch
|
| Heat Deflection Temperature ASTM D-648 | 165° F
|
| Working Time @ 77° F | 20 minutes
|
| Cure Time @77° F | 24 hours
|
|
|
|
| Polygem, Inc. warrants its products to be free of manufacturing defects and that, at the time and place of shipment, our material will meet current physical properties when applied within Polygem’s directions and tested in accordance with ASTM and Polygem standards. Polygem, Inc’s liability is limited to replacement of material found defective. As Polygem, Inc. has no control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and/or our information is valid in a particular circumstance. Responsibility remains with the architect or engineer, contractor and owner for the design, application and proper installation of each product. Nothing contained herein shall be construed to be a recommendation to use or as a license to operate under or to infringe any existing patents.
Data sheets are subject to change without notice, for latest revision check our website at www.polygem.com
|
|
